200 HP Steam Boilers: Used 200 HP Boilers for Sale
200 HP Steam Boilers for Sale
A 200 HP steam boiler is one of the most common sizes in commercial and industrial plants. It is big enough to carry real process load, and small enough to ship on one truck as a packaged unit. That also makes it one of the easiest sizes to find on the used market.
Boilers.com buys and sells used commercial and industrial boilers and ships nationwide from Miami, Florida. Here is what 200 HP means in steam, the published ratings for a 200 HP firetube, the used 200 HP boilers we have listed, and what to check before you buy.
How much steam does a 200 HP boiler make?
One boiler horsepower is the evaporation of 34.5 pounds of water per hour from and at 212°F, which equals about 33,475 Btu/hr of output. So a 200 HP boiler is rated 6,900 lbs/hr of steam (200 × 34.5) and about 6,695,000 Btu/hr.
That is a rating, not a promise at your site. Real steam output is lower when feedwater is cold or operating pressure is high. Size from your actual peak load in lbs/hr at your operating pressure, then add margin.
Pressure matters as much as size. Steam boilers that operate above 15 PSI are power boilers built to ASME Section I and stamped “S”. Low pressure steam boilers, rated 15 PSI or less, are built to ASME Section IV. Most 200 HP units we list are high pressure steam boilers with a 150 PSI or 200 PSI design pressure.
Typical specifications for a 200 HP firetube
The figures below are Cleaver-Brooks published ratings for a 200 HP Model CB packaged firetube. A used boiler’s nameplate is the authority for that specific unit.
Key specs at a glance
Published Cleaver-Brooks ratings for a 200 HP Model CB packaged firetube. Confirm every figure on the nameplate of the unit you buy.
| Item | Rating |
|---|---|
| Boiler horsepower | 200 HP |
| Rated steam capacity | 6,900 lbs/hr from and at 212°F |
| Rated output | 6,695,000 Btu/hr |
| Natural gas at rated capacity | About 8,370 cfh (Model CB) |
| No. 2 light oil at rated capacity | About 60 gph (Model CB) |
| Blower motor | 10 HP on gas-only models, 15 HP on oil or dual fuel models (Model CB) |
| Fireside heating surface | 1,000 sq ft (five sq ft per boiler horsepower) |
| Waterside heating surface | 1,092 sq ft |
| Design | Four-pass dryback packaged firetube |
Those gas and oil figures line up with the nameplates on our used units. Most of our 200 HP Cleaver Brooks listings show an input of about 8,369,000 Btu/hr, and the dual fuel unit lists a 60 GPH maximum oil rate.
The Cleaver Brooks model number tells you the fuel and size. In a model such as CB 700-200, 700 is the fuel series and 200 is the horsepower. Series 700 is gas only, series 200 is No. 2 oil or gas, and series 100 is No. 2 light oil only. A third number, as in CB700-200-200, is usually the design pressure. For more on reading these model numbers, see our guide to the Cleaver Brooks CB700-150.
Used 200 HP steam boilers in stock
Here is a sample of current listings, with figures from each listing’s nameplate or listing data. Inventory changes often, so browse all used boilers and used Cleaver Brooks boilers, or call for the latest.
2014 Cleaver Brooks CBEX-P700-200-150
A used 2014 Cleaver Brooks CBEX-P700-200-150 (yard tag BSCB200HP4340), located in Ohio. It is a packaged firetube steam boiler from the CBEX Premium line, 150 PSI steam, fired on natural gas, built in Thomasville, Georgia. Nameplate input is 8,368,000 Btu/hr. The horsepower comes from the model number and is not stamped on the plate.
Cleaver-Brooks literature for this size lists a 2-pass, water-back design with 671 sq ft of fireside heating surface, about 204 in. overall length, 86 in. overall width, and a shipping weight of about 13,250 lbs at 150 psig. Those are typical figures and may differ on this unit. The National Board number, operating hours, and trim are not confirmed.
Cleaver Brooks CB700-200-200, 200 PSI
A Cleaver Brooks CB700-200-200 (yard tag BSCB200HP192), located in Ohio, for plants that need more than 150 PSI. It is rated 200 PSI steam and fires natural gas, with an input of 8,369,000 Btu/hr and a 10 HP blower motor. Main power is 460 volt, 3 phase, 60 Hz. It is a UL listed gas-fired boiler assembly.
1988 Cleaver Brooks CB 700-200
A 1988 Cleaver Brooks CB 700-200 (yard tag BSCB200HP273), located in Ohio. It is a natural gas packaged steam boiler with a 150 PSI maximum allowable working pressure, serial number L-85045, dated 9/7/88. The electrical package is 3 phase, 60 Hz, with a 120 volt control circuit. It is skid mounted.
Cleaver Brooks CB-500-200C mobile steam plant
A Cleaver Brooks CB-500-200C (yard tag BSCB200HP282), located in Ohio. This is a complete mobile steam plant built inside a 40-foot insulated trailer, and the trailer is included. The boiler is 200 HP, 150 PSI design pressure, and dual fuel: natural gas or No. 2 oil. Maximum gas input is 8,370,000 Btu/hr and maximum oil flow is 60.0 GPH.
It was converted and commissioned by Watco Ltée of Montreal, Quebec, and has Servitech burner management controls with mercury-free water level controls. The trailer also holds a feedwater tank, feed pump, vacuum pump, a three-tank water softener, a 300-gallon steel tank, a 500-gallon diesel/fuel oil tank, and Square D electrical disconnects. That makes it a fit for temporary process steam, emergency backup, or remote sites.
1981 Cleaver Brooks CB-100-200
A 1981 Cleaver Brooks CB-100-200 (yard tag BSCB250HP246), located in Ohio, manufactured August 5, 1981. It is a 200 HP packaged steam boiler, 150 PSI maximum pressure, with an input of 8,369,000 Btu/hr and a 10 HP blower motor. Main power is 230 volt, 3 phase, 60 Hz, and it has an oil pump motor. The listing describes the fuel as natural gas and diesel. In Cleaver Brooks numbering, series 100 left the factory as a No. 2 oil boiler, so confirm the burner and fuel train before you buy.
Need a little more or a little less? We also list 150 HP and 250 HP Cleaver Brooks units. See used Cleaver Brooks 150 HP boilers or browse all used boilers.
What to check before you buy a used 200 HP boiler
A used 200 HP boiler is only a good deal if it fits your load and passes inspection. Inspect it in person, or have a qualified inspector do it, and match every claim to the nameplate and the records.
FAQ
How many lbs of steam is a 200 HP boiler?
A 200 HP boiler is rated 6,900 lbs/hr of steam from and at 212°F, using the standard 34.5 lbs/hr per boiler horsepower. Actual output at your site depends on feedwater temperature, operating pressure, fuel, and the boiler’s condition.
How many Btu is a 200 HP boiler?
The rated output is about 6,695,000 Btu/hr (200 × 33,475). Input is higher. Cleaver-Brooks lists about 8,370 cfh of natural gas for a 200 HP Model CB, and our used units show inputs of about 8,369,000 Btu/hr.
Are your 200 HP boilers high pressure?
Most are. The units listed above are rated 150 PSI, and the CB700-200-200 is rated 200 PSI. Always read the design pressure on the nameplate.
Do you have a portable 200 HP steam boiler?
Yes. The CB-500-200C is a complete dual fuel steam plant inside a 40-foot insulated trailer, with feedwater, water softening, and fuel storage on board. If you need steam right away, also ask about our boiler rentals.
Is a firetube the right type at 200 HP?
For most plants at this size, a packaged firetube is the common choice. If you need very high pressure or much larger loads, read firetube vs watertube boilers.
How do I get pricing?
Our listings are call for price. Call (305) 428-2777 or use our contact page, and tell us the steam load, pressure, fuel, voltage, and timing you need. If you have a 200 HP boiler to sell, see we buy boilers.
Find the right used 200 HP boiler
Start with the 2014 CBEX-P700-200-150 or browse all used boilers for sale. For a quote, help with sizing, or inspection and freight, contact us or call (305) 428-2777. We serve plants nationwide from Miami, Florida.
